Indicateur de rapport de vitesse pour moto Ducati Hyper Motard Hypermotard Hyper Strada Hyperstrada

Description de Indicateur de rapport de vitesse pour moto Ducati Hyper Motard Hypermotard Hyper Strada Hyperstrada

Motorcycle Gear Indicator For Ducati Hyper Motard Hypermotard Hyper Strada Hyperstrada Monster Diesel Gear Display -- Shows the current gear number. Indicates the current gear from 1 to max. 6. As well as a neutral indicator. Detects the current gear faster than other gear indicators that use the speedometer/tachometer signal. Display can be mounted anywhere Preface: Congratulations on purchasing the SEPP gear position indicator, this product will fit all Fuel Injected (EFI) Ducati motorcycles that have a built-in diagnostic system connector. This connector is referred to as DDS (Ducati Diagnostic System) in Ducati manuals. Unlike other gear indicators available for your bike, this product connects to a diagnostic connector. Makes the installation very exemplary. The device reads data directly from the ECU, offering faster and more reliable readings than competing products. Display is auto learning, no button and no "wire programming" know limitations; Your bike is not equipped with a gear position sensor. Therefore, it is only possible to determine the gear used when the engine is running and the clutch is released. Owner's Manual: -Locate the black 4-pole diagnostic connector (also called DDA) under the seat or under the fuel tank -Disconnect the cover (lid) from the plug and connect the gear indicator plug. -Route the cable to the mounting location along the frame. -Remove the green plastic from the back of the device and install the display. - Secure the cable with the provided cable tie. Configuration: -You need to configure the module after installation. When the ignition is turned on, the display will count backwards (from 6 to 1), indicating that the memory is clear. -Raise the rear wheel off the ground with a stand and start the engine in neutral. (If you don't have a stand, you can set up the device while driving. Find a long, straight road with light traffic.) - The display will flash "1". Select first gear, release the clutch and keep the engine speed above idle. The display flashes faster as the device learns to run. -When display shows "2", select two-position. Repeat this process until all gears have been thought through (5 or 6). The device is programmed and should indicate the gears correctly. Now when the ignition is turned on, it will flash forward (1 to 6) to indicate that it is fully functional. Fitment: For Ducati Hyper motard All (2008-2019) For Ducati Hyper Strada All (2013-2019) For Ducati Monster 696 (all year) For Ducati Monster 795 (all year) For Ducati Monster 796 (all year) For Ducati Monster 796 Corse Stripe (all year) For Ducati Monster 797 (all years) For Ducati Monster 821 (2014-2019) For Ducati Monster 1100 (all year) For Ducati Monster 1100 EVO (all years) For Ducati Monster 1200 (2014-2019) For Ducati Monster 1200S (2014-2019) For Ducati Monster 1200R (all years) For Ducati Monster diesel (2012-2013) For Ducati Scrambler 400 (2016-2019) For Ducati Scrambler 800 (2015-2019) For Ducati Scrambler 1000 (2018) -2019) For Ducati Scrambler 1100 (2018-2019) For Ducati Desmosedici RR (2008) For Ducati Supersport 937 (2017-2019) For Ducati Supersport 937S (2017-2019) For Ducati Superbike 848 (2008-2013) For Ducati Superbike 1098 (2009) For Ducati Superbike 1198 (2009-2019) For Ducati Streetfighter (2009-2019)