Productafbeeldingen
Sorry, this item is temporarily out of stock.
For EMID & Card Dual Frequency Access Control Card Reader,Wiegand26/34,UART TTL RFID Card Reader, NFC Card Reader
New
Vergelijkbare producten die je misschien leuk vindt
Would you like us to let you know when it's back?
Beschrijving & Details
Samenvatting
- Product Name: Dual-frequency access control reader; Operating Frequency: 125Khz , 13.56Mhz; Sensing distance: 0-15CM; Operating voltage: DC5-16V; Operating Current: Static Less than 30mA;Dynamic Less than 40mA; Communication format: Wiegand26/34, UART TTL; Working humidity: 10%~90%; Baud rate: 9600.N.8.1; Working temperature: -30℃~85℃; Ways of identifying: Swipe card
- Card reading types: IC card, supports S50, S70 and their compatible cards, M1 card, ID card, EM4100 card etc.(does not support HID, Cobra, APCiK, etc.)IC card, supports S50, S70 and their compatible cards, M1 card, ID card, EM4100 card etc.(does not support HID, Cobra, APCiK, etc.)
- Installation precautions: The line from the card reader to the controller: It is recommended to use an 8-core shielded multi-strand twisted pair network cable (two of which are spare, if the card reader light feedback legal card is not required, the LED cable can not be connected, if the buzzer of the card reader is not used) The Buzzer line can not be connected to the illegal card feedback from the device), and the data lines Data1 and Data0 are a pair of twisted pairs.
- UART TTL RFID Card Reader
- Doorbell NFC Card Reader
For EMID & Card Dual Frequency Access Control Card Reader,Wiegand26/34,UART TTL RFID Card Reader, NFC Card Reader Beschrijving
Product Name: Dual-frequency access control reader; Operating Frequency: 125Khz , 13.56Mhz; Sensing distance: 0-15CM; Operating voltage: DC5-16V; Operating Current: Static Less than 30mA;Dynamic Less than 40mA; Communication format: Wiegand26/34, UART TTL; Working humidity: 10%~90%; Baud rate: 9600.N.8.1; Working temperature: -30~85; Ways of identifying: Swipe card
Card reading types: IC card, supports S50, S70 and their compatible cards, M1 card, ID card, EM4100 card etc.(does not support HID, , APCiK, etc.)IC card, supports S50, S70 and their compatible cards, M1 card, ID card, EM4100 card etc.(does not support HID, , APCiK, etc.)
Installation precautions: The from the card reader to the controller: It is recommended to use an 8-core shielded multi-strand twisted pair network cable (two of which are spare, if the card reader light feedback legal card is not required, the LED cable can not be connected, if the buzzer of the card reader is not used) The Buzzer can not be connected to the illegal card feedback from the device), and the data lines Data1 and Data0 are a pair of twisted pairs.
The wire diameter is recommended to be more than 0.3 square millimeters. The longest can not exceed 100 meters. The shield wire is connected to the GND of the controller.
The card reader is installed a metal surface. Since the card reader is a radio frequency product, the metal pair near the front or the rear will absorb its radio frequency signal. If the metal surface is large, it will even affect the card reader. card, or the reading distance is very attenuated.
The distance between the two card readers will also affect the card reader, some will shorten the card reading distance, and some will cause the two card readers to read the card at the same or the card reader cannot read the card.
Solution: Try not to insta
Details
| OPC | PXQSDPN |
|---|---|
| Codes | 4713734240395 (EAN) |
| Product- en veiligheidsinformatie |
Productgegevens
| Height | 2cm |
|---|---|
| Width | 5cm |
| Length | 5cm |
| Weight | 0.0225kg |
| Colour | As Shown |
| Material | Plastic |
Would you like us to let you know when it's back?
For EMID & Card Dual Frequency Access Control Card Reader,Wiegand26/34,UART TTL RFID Card Reader, NFC Card Reader
New
Misschien vind je dit ook leuk