Mini Wireless Rechargeable Electric Drill Multifunction Motor Tool for Grinding Drilling

Mini Wireless Rechargeable Electric Drill Multifunction Motor Tool for Grinding Drilling Beschrijving

Main featuresIt is very suitable compatible withsanding, drilling and sculpture of works of art and crafts.It is compatible withmanual and specific tasks.It is compatible withdoing pretty little gifts compatible withfamily and friends.We recommend you to read the manual before use and not to use it when the pin is locked.Technical data HAIZI type: 3.6 V lion / 0.6 AhLoad voltage: 100-240 VSize: 3/32 "(2.3 mm)Speed: 5,000/10 000/15 000 rpmPackage content1 * PCG01B 3.6V wireless rotary toolcorresponding kit 1 * 24 pieces1 * USB charging cable with plugSingle three-speed adjustment: a key can change the speed of 5000 rpm, 10000 rpm, 15000 rpm , to adapt to different work environmentsaccording to different forests, 24 accessories help to perform different tasks, such as drilling, grinding, engraving, etc., the size of the mandrel is 3 / 32 "(2.3 mm)Easy to transport with overload protection, safe and reliable work; flexible rubberInstructions compatible withusing electrical toolsusing electrical tools, in order to reduce accidents such as fires, electric shocks and injury, you should pay attention to the basic security features listed below; please read carefully the following security features before continuing.1. Keep the workplace clean and do not use electrical tools in workplaces and messy work surfaces.2. electrical tools in dark and wet locations. Keep it out of the rain. in combustible liquids or where combustible gases exist.3. leave the children and idle on the workplace. The rollers do not allow rollers to approach tactile tools or power cables.4. the power tool is not used, it must be stored in a dry place and out of the reach of children, and must be locked.Keep5. Keep an appropriate speed and pressure speed to make the tool operation safer and more durable.6. Operate according to the specified application range and do not exceed compliance compatible withoverload processing.7. You must maintain a correct posture when you work, you must stay firm and you do not have to stretch your hands on the tools to take things.8. The knives must be lubricated and replaced from time to time to keep them sharpened and the wires must be checked regularly.9. the tools are not used or compatible withmaintenance, when you change the devices and knives, make sure you disconnect the power plug.10. before turning on the s to run the machine. It is necessary to check if the cutting tool adjustment tools and the fastening key are completely removed.11. To avoid accidental startup, you must check if the tool s is turned off before inserting the plug into the power source. power up, do not frequently press your finger on the s .12. Exterior extensions, when using tools outside, be sure to use external extension cords.13. wear ample clothing or accessories to avoid tangling when the tool turns. Rubber gloves and non-slip industrial safety shoes should be worn outside. Protective cap.14. Use safety glasses and wear a mask when there are too many chips and dust.15. walk on the wire, do not slide the wire moving tool and avoid touching the hot object and the pointed metal edge or to wet the fat.16. Secure the room. Use tongs to secure the piece to cut, which is safer than holding the room by hand.17. repairing or replacing parts, be sure to use the parts specified by the plant and send them to a professional replacement repair center.18. Pay attention to the workpiece and tool in unison. Tools should not be used in case of fatigue.19. Before using the tool, you must carefully check if the tool cover or parts are damaged and check if the degree of damage will affect the normal operation of the tool. if all moving parts are in the correct position, if the parts are fixed, etc. If the lid or parts are damaged, if there is a problem with the tool s , please ask a specialized store to repair or replace. a power s that does not work properly to activate the tool.20. During the work, your body should not come into contact with grounded metal objects, such as iron pipes, radiators, refrigerators, etc.