Produktbilder
2X Upa USB Programmer Diagnostic-Tool Upa-USB Ecu Programmer Upa USB V1.3 with Adapter for 2013 Version Main Unit
Ny
I lager
Varför du kommer att älska att handla på OnBuy:
- Tjäna Cashback på varje köp – använd den hur du vill. Spara, spendera eller ta ut.
- Fri frakt – på miljontals produkter på sajten
- Kunder älskar oss – 129,000 recensioner med betyget “Utmärkt”
576,44 kr
678,17 kr
Spara 15%!
+49,43 kr frakt
1 %
Tjäna 5,76 kr direkt
Läs mer
Priserna för varor som säljs av OnBuy inkluderar moms.
Räntefria betalningsalternativ finns tillgängliga
Se fullständig produktbeskrivning och detaljer
Leverans: Standard (49,43 kr) | mån 3e - lör 8e aug
Returer: 30 dagar
180 dagars betalningsskydd
Beskrivning & information
Sammanfattning
- Simply connect the motherboard of the UPA programmer directly or using a DB9 male / female extension cable (1: 1) Insert the correct configuration key into the slot on the main board and start programming via ZIF or DIP female ! You can also use the included DIL to 10 flat ribbon pins, place it inside the ZIF plug and connect a clip or clamps for the use of ISP from there.
- Motorola MCU. Choose the adapter you want to use, connect the flat cable for the adapter (PIN1 is always indicated on both the cable and the adapter) and also on the 10-pin ISP connector on the main board.
- Select the VCC supply source via the bridge on the main board next to the ISP connector (on = target upa supply ... off = target has its own supply). Slide the adapter over the soldered PLCC MCU on the target PCB. (No welding, no pinout revision, no pin counting, saves a lot of time and problems and allows your work to be faster, more accurate and easier). Once your workshop is equipped with our set of adapters, you will have a new UPA experience.
- STMicroelectronics :ST62-40/45/49; NSC：CR16-HCS5(9)/MCS5(9)/MES5(9)/MFS5(9)/MCT5(9)/HCT5(9)
- for Microchip: PIC12F-508/509/629/675,PIC16F-627(A)/628(A)/648A/72/73/74/76/77/818/819/83/84(A)/870/871/872/873(A)/874(A)/876(A)/877(A)
2X Upa USB Programmer Diagnostic-Tool Upa-USB Ecu Programmer Upa USB V1.3 with Adapter for 2013 Version Main Unit Beskrivning
Simply connect the motherboard of the UPA programmer directly or using a DB9 male / female extension cable (1: 1) Insert the correct configuration key into the slot the main board and start programming via ZIF or DIP female ! You can also use the included DIL to 10 flat ribbon pins, place it inside the ZIF plug and connect a clip or clamps for the use of ISP from there.
MCU. Choose the adapter you want to use, connect the flat cable for the adapter (PIN1 is always indicated both the cable and the adapter) and also the 10-pin ISP connector the main board.
Select the VCC supply source via the bridge the main board next to the ISP connector ( = target upa supply ... off = target has its own supply). Slide the adapter over the soldered PLCC MCU the target PCB. (No welding, no pinout revision, no pin counting, saves a lot of and problems and allows your work to be faster, more accurate and easier). Once your workshop is equipped with our set of adapters, you will have a new UPA experience.
STMicroelectronics :ST62-40/45/49; NSC：CR16-HCS5(9)/MCS5(9)/MES5(9)/MFS5(9)/MCT5(9)/HCT5(9)
for Microchip: PIC12F-508/509/629/675,PIC16F-627(A)/628(A)/648A/72/73/74/76/77/818/819/83/84(A)/870/871/872/873(A)/874(A)/876(A)/877(A)
for :
MC68HC05-B6/B8/B16/B16/B32/E6/E6/H12/L28/P3/P3 x /X16/X32
MC68HC08AS20, MC68HC08AS32, MC68HC08AS60, MC68HC08AZ32, MC68HC(9)08AZ32A, MC68HC908AZ60, MC68HC908AZ60A, MC68HC11/A1/A8/E9/EA9, MC68HC11-E20/F1/K4/KA2/KA4/KG4/KS2/KS8/L6/P2/PA8/PH8
MC68HC912-B32/BE32/D60/D60A/DC128A/DG128/DG128A, MC9S12-D64/A128/DG128/DG256/H128/H256
Atmel 8051 Architecture: AT89S-51/52/53/8252/8253
Atmel AVR 8-Bit Risk: AT90S-1200/2313/232/2333/2343/4433/4434/8515/8535, ATmega-8/16/161/162/163/323/64/103/128, ATtiny-12/15/2313
EEPROMs: 24C-01/02/04/08/16/32/64/65/128/256/512, 85C-72
Detaljer
| OPC | PX592QQ |
|---|---|
| Koder | 6032396459739 (EAN) |
| Produkt- och säkerhetsinformation |
Produktdata
| Height | 10cm |
|---|---|
| Width | 15cm |
| Length | 20cm |
| Weight | 0.432kg |
| Colour | red&green&blue |
| Material | Plastic + metal |
Jämför säljare för 2X Upa USB Programmer Diagnostic-Tool Upa-USB Ecu Programmer Upa USB V1.3 with Adapter for 2013 Version Main Unit
- Ny från 625,87 kr
| Säljare | Betyg | Garanti | Returer | Pris | Leverans | Totalt | Antal |
|---|---|---|---|---|---|---|---|
|
Skickas från:
|
(34 recensioner) | - |
30 dagar
Gratis returer Nej
|
576,44 kr
|
+49,43 kr Delivery
Beräknad leverans:
3-8 aug
|
625,87 kr
|
Tjäna medan du handlar med omedelbar Cashback på allt.
Inga krångel, ingen kostnad
- Betalas in på ditt OnBuy-konto
- Använd det vid ditt nästa köp
- Spara det eller ta ut det
Bli en Cashback VIP
Bara 1 köp låser upp bättre erbjudanden och priser