Obrázky produktu
2X Upa USB Programmer Diagnostic-Tool Upa-USB Ecu Programmer Upa USB V1.3 with Adapter for 2013 Version Main Unit
Nové
Skladem
Proč si zamilujete nakupování na OnBuy:
- Získejte Cashback při každém nákupu – využijte jej okamžitě při další objednávce
- Doprava zdarma – u milionů položek na celém webu
- Zákazníci nás mají rádi – 128,000 recenzí s hodnocením “Vynikající”
1 201,94 Kč
1 983,20 Kč
Sleva 39 %!
Doru en zdarma
1%
Získejte 12,02 Kč okamžitě
Zjistěte více
Ceny zboží prodávaného na OnBuy jsou zobrazeny včetně DPH.
Možnosti platby bez úroků k dispozici
Zobrazit kompletní popis a podrobnosti o produktu
Doručení: Standardní (Zdarma) | úte 21 - pon 27 čvc
Prodává: PPEART
Vrácení zboží: 30 dní
180denní ochrana platby
Popis a podrobnosti
Shrnutí
- Simply connect the motherboard of the UPA programmer directly or using a DB9 male / female extension cable (1: 1) Insert the correct configuration key into the slot on the main board and start programming via ZIF or DIP female ! You can also use the included DIL to 10 flat ribbon pins, place it inside the ZIF plug and connect a clip or clamps for the use of ISP from there.
- Motorola MCU. Choose the adapter you want to use, connect the flat cable for the adapter (PIN1 is always indicated on both the cable and the adapter) and also on the 10-pin ISP connector on the main board.
- Select the VCC supply source via the bridge on the main board next to the ISP connector (on = target upa supply ... off = target has its own supply). Slide the adapter over the soldered PLCC MCU on the target PCB. (No welding, no pinout revision, no pin counting, saves a lot of time and problems and allows your work to be faster, more accurate and easier). Once your workshop is equipped with our set of adapters, you will have a new UPA experience.
- STMicroelectronics :ST62-40/45/49; NSC：CR16-HCS5(9)/MCS5(9)/MES5(9)/MFS5(9)/MCT5(9)/HCT5(9)
- for Microchip: PIC12F-508/509/629/675,PIC16F-627(A)/628(A)/648A/72/73/74/76/77/818/819/83/84(A)/870/871/872/873(A)/874(A)/876(A)/877(A)
2X Upa USB Programmer Diagnostic-Tool Upa-USB Ecu Programmer Upa USB V1.3 with Adapter for 2013 Version Main Unit Popis
Simply connect the motherboard of the UPA programmer directly or using a DB9 male / female extension cable (1: 1) Insert the correct configuration key into the slot the main board and start programming via ZIF or DIP female ! You can also use the included DIL to 10 flat ribbon pins, place it inside the ZIF plug and connect a clip or clamps for the use of ISP from there.
MCU. Choose the adapter you want to use, connect the flat cable for the adapter (PIN1 is always indicated both the cable and the adapter) and also the 10-pin ISP connector the main board.
Select the VCC supply source via the bridge the main board next to the ISP connector ( = target upa supply ... off = target has its own supply). Slide the adapter over the soldered PLCC MCU the target PCB. (No welding, no pinout revision, no pin counting, saves a lot of and problems and allows your work to be faster, more accurate and easier). Once your workshop is equipped with our set of adapters, you will have a new UPA experience.
STMicroelectronics :ST62-40/45/49; NSC：CR16-HCS5(9)/MCS5(9)/MES5(9)/MFS5(9)/MCT5(9)/HCT5(9)
for Microchip: PIC12F-508/509/629/675,PIC16F-627(A)/628(A)/648A/72/73/74/76/77/818/819/83/84(A)/870/871/872/873(A)/874(A)/876(A)/877(A)
for :
MC68HC05-B6/B8/B16/B16/B32/E6/E6/H12/L28/P3/P3 x /X16/X32
MC68HC08AS20, MC68HC08AS32, MC68HC08AS60, MC68HC08AZ32, MC68HC(9)08AZ32A, MC68HC908AZ60, MC68HC908AZ60A, MC68HC11/A1/A8/E9/EA9, MC68HC11-E20/F1/K4/KA2/KA4/KG4/KS2/KS8/L6/P2/PA8/PH8
MC68HC912-B32/BE32/D60/D60A/DC128A/DG128/DG128A, MC9S12-D64/A128/DG128/DG256/H128/H256
Atmel 8051 Architecture: AT89S-51/52/53/8252/8253
Atmel AVR 8-Bit Risk: AT90S-1200/2313/232/2333/2343/4433/4434/8515/8535, ATmega-8/16/161/162/163/323/64/103/128, ATtiny-12/15/2313
EEPROMs: 24C-01/02/04/08/16/32/64/65/128/256/512, 85C-72
Podrobnosti
| OPC | PVXGDFD |
|---|---|
| Kódy | 4714060667153 (EAN) |
| Informace o produktu a bezpečnosti |
Produktová data
| Height | 10cm |
|---|---|
| Width | 13cm |
| Length | 19cm |
| Weight | 0.306kg |
| Colour | red&green&blue |
| Material | Plastic + metal |
Porovnejte prodejce pro 2X Upa USB Programmer Diagnostic-Tool Upa-USB Ecu Programmer Upa USB V1.3 with Adapter for 2013 Version Main Unit
- Nové od 1 201,94 Kč
| Prodejce | Hodnocení | Záruka | Vrácení zboží | Cena | Doručení | Celkem | Množství |
|---|---|---|---|---|---|---|---|
|
Odesláno z:
|
(317 recenzí) | - |
30 dní
Vrácení zboží zdarma Ne
|
1 201,94 Kč
|
+Free Delivery
Odhadované doručení:
21-27 čvc
|
1 201,94 Kč
|
Získávejte odměny při nákupu s okamžitým Cashback na vše.
Žádný háček, žádné náklady
- Připsáno na váš účet OnBuy
- Využijte je při dalším nákupu
- Ušetřete nebo si je vyberte
Staňte se Cashback VIP
Už po 1 nákupu získáte lepší nabídky a ceny