6Pcs SHT31-D Temperature Humidity Sensor Digital Output Sensor Module IIC I2C Interface 3.3V for Raspberry Pi
Σε απόθεμα
Γιατί θα λατρέψεις τις αγορές στην OnBuy :
- Κέρδισε Επιστροφή Ποσού σε κάθε αγορά – ξόδεψε το άμεσα στην επόμενη παραγγελία σου
- Δωρεάν παράδοση – σε εκατομμύρια προϊόντα σε όλο το site
- Οι πελάτες μας λατρεύουν – 132,000 κριτικές με βαθμολογία « Άριστα »
Οι τιμές για τα είδη που πωλούνται από την OnBuy περιλαμβάνουν ΦΠΑ.
Διαθέσιμες άτοκες επιλογές πληρωμής
Δες την πλήρη περιγραφή & λεπτομέρειες του προϊόντος
Παράδοση: Κανονικό (13,56 €) | Τρι 1 - Δευ 7 Σεπ
Πωλείται από: CollBea
Επιστροφές: 30 ημέρες
Προστασία πληρωμής 180 ημερών
Μπορεί επίσης να σου αρέσουν
Περίληψη
- Supply voltage range: 2.4 to 5.5V (typically 3.3V)
- RH working range: 0-99.99%RH ; I2C interface, communication rate up to 1MHz, with two user-selectable addresses
- Operating temperature range: -40 to 125Celsius (-40 to 257Fahrenheit)
- RH response time: 8 seconds (tau63%)
- Typical accuracy is +/- 2% RH and +/- 0.3 inch with high accuracy
6Pcs SHT31-D Temperature Humidity Sensor Digital Output Sensor Module IIC I2C Interface 3.3V for Raspberry Pi Περιγραφή
Supply voltage range: 2.4 to 5.5V (typically 3.3V)
RH working range: 0-99.99%RH ; I2C interface, communication rate to 1MHz, with two user-selectable addresses
Operating temperature range: -40 to 125Celsius (-40 to 257Fahrenheit)
RH response : 8 seconds (tau63%)
Typical accuracy is +/- 2% RH and +/- 0.3 inch with high accuracy
Sensor Manufacturer: #SHT31-DIS
RH response : 0- RH
Interface: I2C
Power Pins:
Vin - this is the power pin. The chip can use 2.5-5VDC for power. To power the board, give it the same power as the logic level of your microcontroller - e.g. for a 5V like for , use 5V. For a 3.3V controller like a Raspbery Pi, connect to 3.3V GND - common ground for power and logic
SCL - I2C clock pin, connect to your microcontrollers I2C clock . This pin has a 10K pullup resistor to Vin
SDA - I2C data pin, connect to your microcontrollers I2C data . This pin has a 10K pullup resistor to Vin
ADR - This is the I2C address selection pin. This pin has a 10K pull down resistor to make the default I2C address 0x44. You can tie this pin to Vin to make the address 0x45
RST - Hardware reset pint. Has a 10K pullup it to make the chip active by default. Connect to ground to do a hardware reset!
ALR - Alert/Interrupt output. You can set the sensor to alert you when an event has occured. Check the datasheet for how you can set the alerts
Colour:Photo Color
Material:plastic
Package Contents:
6 x SHT31-D Temperature Humidity Sensor
Λεπτομέρειες
| OPC | PWN8NXJ |
|---|---|
| Κωδικοί | 6034077253216 (EAN) |
| Πληροφορίες προϊόντος και ασφάλειας |
Στοιχεία Προϊόντος
| Height | 2cm |
|---|---|
| Width | 7cm |
| Length | 5cm |
| Weight | 0.013kg |
| Colour | Photo Color |
| Material | plastic |
Σύγκρινε Πωλητές για 6Pcs SHT31-D Temperature Humidity Sensor Digital Output Sensor Module IIC I2C Interface 3.3V for Raspberry Pi
- Νέο από 45,88 €
| Πωλητής | Αξιολογήσεις | Εγγύηση | Επιστροφές | Τιμή | Παράδοση | Σύνολο | Ποσότητα |
|---|---|---|---|---|---|---|---|
|
Αποστολή από:
|
(206 αξιολογήσεις) | - |
30 ημέρες
Δωρεάν επιστροφές Όχι
|
32,31 €
|
+13,56 € Delivery
Εκτ. Παράδοση:
1-7 Σεπ
|
45,88 €
|
Κέρδισε καθώς ψωνίζεις με άμεσο Cashback σε όλα.
Χωρίς παγίδες, χωρίς κόστος
- Καταβάλλεται στον λογαριασμό σας στο OnBuy
- Ξόδεψέ το στην επόμενη αγορά σου
- Αποθήκευσέ τα ή κάνε ανάληψη
Γίνετε Cashback VIP
Μόνο 1 αγορά ξεκλειδώνει μεγαλύτερες προσφορές και καλύτερα ποσοστά