6Pcs SHT31-D Temperature Humidity Sensor Digital Output Sensor Module IIC I2C Interface 3.3V for Raspberry Pi
På lager
Derfor vil du elske å handle hos OnBuy:
- Tjen Cashback på hvert kjøp – bruk det umiddelbart på din neste bestilling
- Gratis levering – på millioner av varer på hele nettstedet
- Kunder elsker oss – 132,000 anmeldelser med vurderingen “Utmerket”
Prisene for varer solgt av OnBuy inkluderer mva.
Rente- og gebyrfri delbetaling tilgjengelig
Se full produktbeskrivelse og detaljer
Levering: Standard (4,03 kr) | tir 1. - man 7. sep
Solgt av: CollBea
Returer: 30 dager
180 dagers betalingsbeskyttelse
Du vil kanskje også like
Sammendrag
- Supply voltage range: 2.4 to 5.5V (typically 3.3V)
- RH working range: 0-99.99%RH ; I2C interface, communication rate up to 1MHz, with two user-selectable addresses
- Operating temperature range: -40 to 125Celsius (-40 to 257Fahrenheit)
- RH response time: 8 seconds (tau63%)
- Typical accuracy is +/- 2% RH and +/- 0.3 inch with high accuracy
6Pcs SHT31-D Temperature Humidity Sensor Digital Output Sensor Module IIC I2C Interface 3.3V for Raspberry Pi Beskrivelse
Supply voltage range: 2.4 to 5.5V (typically 3.3V)
RH working range: 0-99.99%RH ; I2C interface, communication rate to 1MHz, with two user-selectable addresses
Operating temperature range: -40 to 125Celsius (-40 to 257Fahrenheit)
RH response : 8 seconds (tau63%)
Typical accuracy is +/- 2% RH and +/- 0.3 inch with high accuracy
Sensor Manufacturer: #SHT31-DIS
RH response : 0- RH
Interface: I2C
Power Pins:
Vin - this is the power pin. The chip can use 2.5-5VDC for power. To power the board, give it the same power as the logic level of your microcontroller - e.g. for a 5V like for , use 5V. For a 3.3V controller like a Raspbery Pi, connect to 3.3V GND - common ground for power and logic
SCL - I2C clock pin, connect to your microcontrollers I2C clock . This pin has a 10K pullup resistor to Vin
SDA - I2C data pin, connect to your microcontrollers I2C data . This pin has a 10K pullup resistor to Vin
ADR - This is the I2C address selection pin. This pin has a 10K pull down resistor to make the default I2C address 0x44. You can tie this pin to Vin to make the address 0x45
RST - Hardware reset pint. Has a 10K pullup it to make the chip active by default. Connect to ground to do a hardware reset!
ALR - Alert/Interrupt output. You can set the sensor to alert you when an event has occured. Check the datasheet for how you can set the alerts
Colour:Photo Color
Material:plastic
Package Contents:
6 x SHT31-D Temperature Humidity Sensor
Detaljer
| OPC | PWN8NXJ |
|---|---|
| Koder | 6034077253216 (EAN) |
| Produkt- og sikkerhetsinformasjon |
Produktdata
| Height | 2cm |
|---|---|
| Width | 7cm |
| Length | 5cm |
| Weight | 0.013kg |
| Colour | Photo Color |
| Material | plastic |
Sammenlign selgere for 6Pcs SHT31-D Temperature Humidity Sensor Digital Output Sensor Module IIC I2C Interface 3.3V for Raspberry Pi
- Ny fra 315,63 kr
| Selger | Vurderinger | Garanti | Returer | Pris | Levering | Totalt | Antall |
|---|---|---|---|---|---|---|---|
|
Sendt fra:
|
(206 anmeldelser) | - |
30 dager
Gratis retur Nei
|
311,60 kr
|
+4,03 kr Delivery
Estimert levering:
1-7 sep
|
315,63 kr
|
Tjen mens du handler med umiddelbar Cashback på alt.
Ingen binding, ingen kostnad
- Utbetalt til OnBuy-kontoen din
- Bruk det på neste kjøpet ditt
- Spar den eller ta den ut
Bli en Cashback VIP
Bare 1 kjøp gir deg større rabatter og bedre priser