6Pcs SHT31-D Temperature Humidity Sensor Digital Output Sensor Module IIC I2C Interface 3.3V for Raspberry Pi
Raktáron
Ezért fogod szeretni az OnBuy-on való vásárlást:
- Szerezz Cashback pénzvisszatérítést minden vásárlás után, és költsd el azonnal a következő rendelésnél.
- Ingyenes kiszállítás – több millió termékre az oldalon
- Vásárlóink elégedettek velünk, már 132,000 Kiváló értékelést kaptunk!
Az OnBuy-on értékesített termékek ára tartalmazza az áfát.
Teljes termékleírás és részletek megtekintése
Kézbesítés: Normál (2 899,65 Ft) | sze 2. - kedd 8. szept.
Eladó: CollBea
Visszaküldés: 30 nap
180 napos fizetési védelem
Ez is érdekelhet
Összefoglaló
- Supply voltage range: 2.4 to 5.5V (typically 3.3V)
- RH working range: 0-99.99%RH ; I2C interface, communication rate up to 1MHz, with two user-selectable addresses
- Operating temperature range: -40 to 125Celsius (-40 to 257Fahrenheit)
- RH response time: 8 seconds (tau63%)
- Typical accuracy is +/- 2% RH and +/- 0.3 inch with high accuracy
6Pcs SHT31-D Temperature Humidity Sensor Digital Output Sensor Module IIC I2C Interface 3.3V for Raspberry Pi leírása
Supply voltage range: 2.4 to 5.5V (typically 3.3V)
RH working range: 0-99.99%RH ; I2C interface, communication rate to 1MHz, with two user-selectable addresses
Operating temperature range: -40 to 125Celsius (-40 to 257Fahrenheit)
RH response : 8 seconds (tau63%)
Typical accuracy is +/- 2% RH and +/- 0.3 inch with high accuracy
Sensor Manufacturer: #SHT31-DIS
RH response : 0- RH
Interface: I2C
Power Pins:
Vin - this is the power pin. The chip can use 2.5-5VDC for power. To power the board, give it the same power as the logic level of your microcontroller - e.g. for a 5V like for , use 5V. For a 3.3V controller like a Raspbery Pi, connect to 3.3V GND - common ground for power and logic
SCL - I2C clock pin, connect to your microcontrollers I2C clock . This pin has a 10K pullup resistor to Vin
SDA - I2C data pin, connect to your microcontrollers I2C data . This pin has a 10K pullup resistor to Vin
ADR - This is the I2C address selection pin. This pin has a 10K pull down resistor to make the default I2C address 0x44. You can tie this pin to Vin to make the address 0x45
RST - Hardware reset pint. Has a 10K pullup it to make the chip active by default. Connect to ground to do a hardware reset!
ALR - Alert/Interrupt output. You can set the sensor to alert you when an event has occured. Check the datasheet for how you can set the alerts
Colour:Photo Color
Material:plastic
Package Contents:
6 x SHT31-D Temperature Humidity Sensor
Részletek
| OPC | PWN8NXJ |
|---|---|
| Kódok | 6034077253216 (EAN) |
| Termék- és biztonsági információk |
Termékadatok
| Height | 2cm |
|---|---|
| Width | 7cm |
| Length | 5cm |
| Weight | 0.013kg |
| Colour | Photo Color |
| Material | plastic |
Eladók összehasonlítása: 6Pcs SHT31-D Temperature Humidity Sensor Digital Output Sensor Module IIC I2C Interface 3.3V for Raspberry Pi
- Új innen 15 376,42 Ft
| Eladó | Értékelések | Garancia | Visszaküldések | Ár | Kiszállítás | Összesen | Mennyiség |
|---|---|---|---|---|---|---|---|
|
Feladás helye:
|
(206 értékelés) | - |
30 nap
Ingyenes visszaküldés Nem
|
12 476,77 Ft
|
+2 899,65 Ft Delivery
Várható szállítás:
2-8 szept.
|
15 376,42 Ft
|
Vásárlás közben is keressen pénzt azonnali Cashback-kel minden termékre.
Nincs apróbetűs rész, nincs költség
- Jóváírva az OnBuy-fiókján
- Költse el a következő vásárlásán
- Gyűjtse vagy vegye fel
Legyen Cashback VIP-tag
Már egyetlen vásárlással is nagyobb kedvezményeket és jobb árakat érhet el