Bond it STERI-GROUT Floor & Wall Tile Grout 3KG White

Bond it STERI-GROUT Floor & Wall Tile Grout 3KG White Description

Description: A specially formulated, polymer modified cement based floor and wall tile grout. Recommended for sanitary installations ie. kitchens, bathrooms, toilets and shower rooms. Containing a strong fungicide it will also inhibit black spot mould growth. Conforms to EN 13888: CGW2. Uses STERI-GROUT is suitable for use in areas of limited movement/ vibration so ideal for use over timber ply-boards and heated subfloors. Recommended for sanitary installations ie. kitchens, bathrooms, power showers, toilets and shower rooms. This grout has excellent adhesion characteristics to porcelain and fully vitrified tiles, has low permeability and reduced dirt pick up. Containing a strong fungicide it will also inhibit black spot mould growth. Can be used in interior and exterior locations. Preparation Check that all the tiles are securely fixed and that the tile adhesive has thoroughly dried before applying any load or pressure to the tiled surface. Allow adhesive to set sufficiently before applying grout. Ensure joints are clean, dry and free from dust and obstructions. Use only in joints from 1mm-20mm wide. It is recommended that current best practice e.g. current TTA or COP guidelines are always followed. Mixing STERI-GROUT powder should be added to clean water, Mix the powder with clean water (approx. 750ml: 3Kg bag) to a thick, creamy paste by either hand or slow speed mixing drill and paddle. When mixing by hand allow the mixed grout to stand for a few minutes then remix to ensure an even consistency. Do not mix more than can be used in a 30-60 minute period. Partused grout should never be "freshened up" by adding more water, discard any grout once it appears to lose workability. Application Using a grouting tool, sponge or squeegee, work the mixed grout thoroughly into dry tile joints ensuring the joints are completely filled. Remove excess grout from the face of tiles with a damp sponge or cloth. Use a suitable tool to compact the grout into joints. After initial hardening of the grout, clean the tile surface using a clean dampened sponge working diagonally across the grout lines. Once the grout is set polish the tiles with a soft cloth. Protect from damp for 24 hours after grouting. Clean tools after use with warm water. Mechanical means may be necessary when product has set. Open Time Open time of the exposed adhesive bed is approx. 20 minutes, dependant on conditions. Pot life approx 30-60 minutes @ 20oC. Drying Time Final set will occur between 12-24 hours. Cement based products will take longer to harden and set at lower temperatures and should not be used below 5o C. Light foot traffic: after 12 hours; Full traffic: after 24-48 hours (dependant on site conditions). Limitations Slight colour variation may occur between batches. Colour variation will occur under different mixing and/or site conditions. Any cement film should be removed as soon as possible with an acid based cleaner. Always pre-wet joints when using an acid based cleaner. When grouting textured and slip-resistant tiles, ensure grout residue is throughly cleaned off before it has set. Please note: Certain tiles may suffer from discolouration or scratching when using grouts. We would recommend that a test application be carried out prior to grouting. Our grouts go through stringent checks to ensure quality and colour, however due to the use of raw materials we suggest a trial area to ensure colour is consistent and as expected. Coverage This will vary depending on the tile size, joint depth and width. Approximately 1Kg of STERI-GROUT will grout 2m2 of 300 x 300mm tiles with a 5mm joint. Cleaning Tools should be washed with water immediately after use with warm water. Container Size 3Kg plastic sacks. Colour White Never compromise on quality! Shelf Life 12 months from date of manufacture when stored in unopened bags. Storage Conditions Store in original, unopened sacks, off the ground, in cool, dry conditions and away from excessive draughts. Disposal of Containers Do not leave empty containers where residue could be harmful to children, animals or the environment. Remove any bags or material to a central disposal point in accordance with local regulations. Health & Safety Please refer to separate material safety data sheet for full handling, use and storage instructions. Keep out of reach of children. It is the users responsibility to determine suitability for use. If in doubt contact our Technical Department for advice. Note: this information is for general guidance only, since site conditions and labour are beyond our control. It is recommended that users make their own tests to determine suitability. Specification Summary Flammability Non-flammable Application Temperature +5 to +30oC Working Time 1 Hour Joint Width 1-20mm Compressive Strength > 15MPa Flexural Strength >2.5 MPa Shrinkage