(Flake White) Plasti Dip Paint - Tints-All Colourant - 8 Fl. Oz.

(Flake White) Plasti Dip Paint - Tints-All Colourant - 8 Fl. Oz. Description

Tints-All Colourant

A Shade Further...

Tints-All is a lead free colourant that can be added to Plasti Dip, allowing you to customize your coating to the exact shade you require.  It can also be used for tinting Latex, Alkyds, Oil, Acrylic and Polyvinyl, cement and concrete, enamels and some epoxies without affecting the performance of the product. It is a professional formulation suitable for interior and exterior applications, providing you with a broad range of mixing possibilities. This range of finest quality pigments offers a stunning colour selection for a high quality finish.

8 Fl. Oz. bottles 

Plasti Dip is a flexible air-dried, synthetic rubber liquid matt coating that can be used on virtually anything!

Plasti Dip resists moisture, acids, salts, abrasion, corrosion, weathering, most chemicals and skidding.  It is an insulating dielectric coating.  It will not crack, chip or peel and remains flexible even under severe conditions (-34ºc to +93ºc).  The coating provides safe, non-slip comfort grip and control.

Plasti Dip can be dipped, brush coated or sprayed. Add more layers for greater protection and grip.

NOTE: Surfaces which are non-absorbent such as metals should be primed using our recommended Primers, which are available in Clear and Grey.

PLEASE READ: Guide to Preparation and Application

The essential criteria is to ensure the surface is squeaky clean, grease, dirt, debris and contaminant free and thoroughly dry before coating.

On vehicles or irregular shaped items, particular attention should be paid to the sills, trim, gutters, grills, any tight or hard to get to corners and gullies that you would not normally concentrate on.

Wash only with hot water as some soap detergents contain residues that Plasti Dip may not adhere to.
Never use any petroleum, citric, alcohol or solvent based cleaning/care products with Plasti Dip.
Do not use car care cleaning products such as wheel shines, paint wipes etc, as these often leave trace residues which could cause adhesion problems.
Remove all traces of previous wax or silicone residue from cleaning products using the correct de-greaser, particularly for metal and plastic surfaces.
Clean large areas with Plasti Dip Panel Wipe degreaser.
Small areas can be cleaned with Plasti Dip “Dip Care Prep Degreaser”.
Ensure all water is removed and the area thoroughly dry before coating.

In common with all manufacturer's advice, we recommend testing on a small inconspicuous area first to ensure suitability. Base colours can alter the final shade.

If spraying, for a professional fine finish, Plasti Dip liquid should be filtered first. For best results, temperature of the spraying area should be between 10°c and a maximum of 27°c. Liquid Plasti Dip should be thinned 50/50 by weight. Apply the first coat as a mist coat and gradually build up the layers. The thicker the final coating, the easier it is to remove in the future should you wish. For vehicles, we suggest a minimum of 6-7 coats. For other projects a minimum of 2-4 coats is recommended depending on application method and coverage requirement.

Layers are touch dry and re-coatable in 30-45 minutes at 16-22°c and totally cured/dry 24-48 hours depending on temperature. Increase drying times in colder conditions.

Plasti Dip Primer is an adhesion promoter. Only use a primer to increase adhesion if you require a permanent coating. For permanent application, keying the surface with fine grit paper will improve adhesion if required.

For extra protection of your investment and ease of cleaning, we recommend using Dip Care Sealant over the final coating.

Please see our booklet supplied with your order for other handy tips and product information, including spray gun settings.

If you have any concerns about the correct products or procedures for your project, please feel free to contact us.