Performix - Plasti Dip Enhancer - Glossifier (Clear Gloss) - SPRAY

Performix - Plasti Dip Enhancer - Glossifier (Clear Gloss) - SPRAY Description

Plasti Dip - The Original Peelable, Flexible, Insulating, Non-Slip, Durable, Rubber Coating!

Plasti Dip Glossifier is a clear gloss top-coat that can be applied over Plasti Dip.

Used on its own, PLASTI DIP gives a matte finish. When Glossifier is used as an 'over coat' in combination with touch dry Plasti Dip, it dries to a high quality gloss finish.

Glossifier will also improve tensile strength, abrasion, block resistance and overall durability.

Plasti Dip Glossifier is ideal for a broad range of uses, from arts and crafts to home improvement projects and more.

Plasti Dip Enhancers are formulated to bond with the unique chemical structure of cured Plasti Dip for superior adhesion and long life.

(Plasti Dip Enhancers are not recommended for use on any other surface).

To spray the Glossifier using a spray gun it will need to be thinned with Plasti Dip Thinners by 10%

PlastiDip can be dipped, brush coated and sprayed. Add more layers for greater protection and grip.

Also... PLASTIC, RUBBER, FIBREGLASS and CONCRETE SURFACES!

NOTE: Surfaces which are non-absorbent such as metals should be primed using our recommended Primers, which are available in Clear and Grey.

PLEASE READ: Guide to Preparation and Application

The essential criteria is to ensure the surface is squeaky clean, grease, dirt, debris and contaminant free and thoroughly dry before coating.

On vehicles or irregular shaped items, particular attention should be paid to the sills, trim, gutters, grills, any tight or hard to get to corners and gullies that you would not normally concentrate on.

Wash only with hot water as some soap detergents contain residues that Plasti Dip may not adhere to.
Never use any petroleum, citric, alcohol or solvent based cleaning/care products with Plasti Dip.
Do not use car care cleaning products such as wheel shines, paint wipes etc, as these often leave trace residues which could cause adhesion problems.
Remove all traces of previous wax or silicone residue from cleaning products using the correct de-greaser, particularly for metal and plastic surfaces.
Clean large areas with Plasti Dip Panel Wipe degreaser.
Small areas can be cleaned with Plasti Dip “Dip Care Prep Degreaser”.
Ensure all water is removed and the area thoroughly dry before coating.

AEROSOLS – Refer to aerosol for instructions. Shake well before and during use. Test spray pattern on sample piece prior to application. In cold conditions, place aerosol in warm water (approximately 21°c) for 10-15 minutes before use.

BLAZE COLOURS – Best applied over white Plasti Dip base coat.

In common with all manufacturer's advice, we recommend testing on a small inconspicuous area first to ensure suitability. Base colours can alter the final shade.

If spraying, for a professional fine finish, Plasti Dip liquid should be filtered first. For best results, temperature of the spraying area should be between 10°c and a maximum of 27°c. Liquid Plasti Dip should be thinned 50/50 by weight. Apply the first coat as a mist coat and gradually build up the layers. The thicker the final coating, the easier it is to remove in the future should you wish. For vehicles, we suggest a minimum of 6-7 coats. For other projects a minimum of 2-4 coats is recommended depending on application method and coverage requirement.

Layers are touch dry and re-coatable in 30-45 minutes at 16-22°c and totally cured/dry 24-48 hours depending on temperature. Increase drying times in colder conditions.

Plasti Dip Primer is an adhesion promoter. Only use a primer to increase adhesion if you require a permanent coating. For permanent application, keying the surface with fine grit paper will improve adhesion if required.

For extra protection of your investment and ease of cleaning, we recommend using Dip Care Sealant over the final coating.

Please see our booklet supplied with your order for other handy tips and product information, including spray gun settings.

If you have any concerns about the correct products or procedures for your project, please feel free to contact us.