Programmable Controller Module Offline Sequence Control DC12-24V

Programmable Controller Module Offline Sequence Control DC12-24V Description

1、PROGRAMMABLE FUNCTION: This offline sequence controller has programmable function, which can be customized to set up a great sequence trace according to actual requirements. 2、BASIC VALUES: This programmable offline sequence controller has an operating voltage of DC12 to 24V, a screen structure of 5 digits and a high brightness digital tube. 3、USE SCENARIO: Our programmable off line serial controller is widely applied in industrial automation control, small mechanical devices. 4、MADE OF PC MATERIAL: The programmable offline sequence controller is made of PC material, which is strong and durable. 5、LIGHT WEIGHT: Our programmable offline sequence controller is light weight and easy to install and very practical and helpful.
Item Type: Programmable controller
Material: PC
Housing Size: Approx. 99.7 x 72 x 17mm / 3.93 x 2.83 x 0.67in (L x W x H)
Screen Structure: 5 digit, high brightness digital tube
Operating Environment: -5- 60 (no condensation)
Opening Size: Approx. 92 x 69.8mm / 3.62 x 2.75in (L x W)
Input: 5 programmable inputs, 2 fixed inputsSerial numberFunctionRangeDefault valueF0Cycle working times Unit: times (demonstrated below) 0-65534, 65535 for countless times1F1Number of rows at the beginning of the loop Unit: rows (Demonstrated below)0-400If the number of lines at the beginning of the loop > the number of lines at the end of the loop, it is illegal. Will alarmF2Number of rows at the end of the loop Unit: rows (demonstrated below)0-4040Illegal if the number of lines at the beginning of the loop > the number of lines at the end of the loop. Will alarmF3Open [Output] manual debugging interface (restart to exit automatically or press [Return])Introduced below0F4Open [Input] manual debugging interface (restart to exit automatically or press [Return])Introduced below0F5Turn on programming mode (restart to exit automatically)0-10If you do not turn on the programming privileges, it is not possible to change the programming statements and alarm0: Turn off programming privileges (power off automatically changes to 0)
1: Turn on programming privilegesF15Adjust the amplitude value of [overall working time] during operation
Unit:second0-65535.999 , 0=no speed change during operation0F16Auto run at power on specified program line: 31-40 lines0-200 Turn off. If turned off, program segment 31-40 lines will automatically act as normal program category1 Power on automatically runs program segment 31-40 lines.
2 The power on automatically works.F17Action when ESC emergency stop key is pressed0-200 Program ends and turns off all outputs 1 Program ends and holds current state2 Program ends and runs program segment lines 31-40If parameter 2 is not selected, then program lines 31-40 automatically act as normal program categoriesF18Selectively switch P interface or F interface 0-301 Off [P interface] on [F interface]
2 On [P interface] off [F interface]3 All off (temporary open: press [Set] key before power on)
0 All onF19Main interface display content 0-200 Realtime working status. Display the total number of working times (not the number of cycles) under standby 1 Displays the number of cycles (not the total number) 2 Displays what line of program the system is runningF20Port filtering time of input port 0-65535120Set again when there is external interference. The higher the value, the slower the response Unit: LevelF21Start or emergency stop button signal filtering time on the panel 0-6553527Set again when there is external interference. The higher the value, the slower the response Unit: LevelF24Restore the factory setting 0-44Note: After changing this parameter, you need to power off and restart1 Restore [F] parameter only
2 Restore [P] parameter only3 Restore all
4 No need to restore 0 or >10: restore all and open self test mode, factory mode (only for factory use)
1 x Programmable Controller