30V Constant Current Electronic Load Module Battery Tester 60W

30V Constant Current Electronic Load Module Battery Tester 60W Description

1、Simple and versatile electronic load 2、Automatic memory function with all parameters 3、Well suite automated assembly of the power adapter aging module 4、Higher cooling redundancy, more suitable for long hours 5、Multifunctional, can also be used to test battery
Description:
New design, simple and versatile electronic load! Automatic memory function with all parameters , is well suited for
automated assembly of the power adapter aging(burn-in) module.
Features:
1, Simple and versatile electronic load.
2, Automatic memory function with all parameters , is well suited for
automated assembly of the power adapter burn-in module.
3, In the sale
of the latest version, slightly larger size and upgrade the fan into
the original 5020 Delta high speed dual bearing fan.
4, Higher cooling
redundancy, more suitable for long hours.
5, Multi-functional, can also be used to test battery.
Specifications:
Operating Modes: Single mode constant current (CC).
Discharge current: 0.20-9.99A stepper 0.1A or 0.01A
Discharge Current Maximum Error: 0.7% -0.01A
The Maximum Capacity Test Error: 0.5A 2.5%, 2A 1.5%, 5A and above 1.2%
Maximum Power: 60W super power automatically limits the maximum current (for
example, up to 60W when it can open 9.99A 6V and 20V maximum at the only
open 3.00A)
Highest Battery Test Statistic: 999.9Ah or 9999Wh, achieve value stop testing ( first value to those who stop condition )
Board Size: 60W 100mm x 70mm x 57mm ( fan prominent board about 12mm)
Positioning Hole Locations: 60mm x 88mm diameter 3.2mm 5mm pedestal already installed
Weight: 184g(approx.)
Fan Control: intelligent fan control ( according to the radiator fan can be infinitely variable automatic temperature )
Instructions:
A: Mode Settings ( default factory for electronic load mode ) : Hold down
the start-stop button ( red button ) to the tester simultaneously
energized until the key is released showing Fun * When , by rotating the
knob to change the setting , "Fun1" for electronic load mode , "Fun2"
battery capacity test mode. Push button start and stop at the buzzer
after entering the settings, also set "bEon" buzzer by turning the knob
to open or "bEoF" buzzer closes After setting press the button again to
start and stop at the tester restart.
Setting Digital Illustration:
II: Electronic Load Mode:
1.
Turn on the power supply 12V boot into electronic load mode , ensuring
in a stopped state ("RUN" does not light, otherwise the press of the
start-stop switch to turn off the load ) connected to the power supply
under test to the test port input power (P+ P- ) , pay attention not
to take the wrong polarity !
Note: When
in alarm state, can only transfer a small current does not increase
!Tester automatic power-down feature to save enough to save the set
parameters and run state, when the state again after power transmission
will complete before the power failure and restore data.
Battery Capacity Test Mode:
1. The test battery should be fully charged with a special charger.
Additional Information:
2. Tester automatic storage can
record setting parameters , and record all parameters and status at the
end of the test process and test power failure alarm status , re-
transmission of all automatically restored.
Fault protection codes and meanings:
Err3: line resistance is too large or the battery can not afford to set the discharge current.
Err4: circuit failure .
Err6: working power is inappropriate , use a standard 12V power supply , and the supply current is not less than 0.5A.
otP: overheating protection.
Ert: temperature sensor failure or the temperature is too low.
ouP: ultra-high voltage electron -load mode.
oPP: under ultra-high power electronic load mode instantly.
Package Includes:
1 x Multi-function Module
Note:
1, This product is a professional testing equipment , requiring the user have some basic electronic knowledge, or you
may be unable to use the device properly, possibly mishandled cause
unnecessary loss caused by the test device damage.
2, The default power adapter is not included.
3, Please allow 1-3mm error due to manual measurement. Thanks for your understanding.