(Blue) Plasti Dip Glow Spray Aerosol - Luminous!

(Blue) Plasti Dip Glow Spray Aerosol - Luminous! Description

IMPORTANT PLEASE SEE PREPARATION AND APPLICATION GUIDE SUPPLIED WITH YOUR ORDER TO ENSURE BEST RESULTS

Plasti Dip - The Original Peelable, Flexible, Insulating, Non-Slip, Durable, Rubber Coating!

PlastiDip is an air dried flexible liquid matt coating for use on virtually anything!

This Plasti Dip makes your object visible in the dark !!!

The surface sprayed with Plasti Dip Glow in The Dark will store the light and will reflect once in the dark. More light will be captured, the more light will be enacted.

Plastidip spray is a paint spray which allows to repaint your surfaces in a simple and reversible. Instantaneous and suitable for any type of object, this paint can is the easiest and fastest way to create a protective film resistant and homogeneous.

Sealant, abrasion and temperature-resistant from -35 ° C to +93 ° C, PLASTI DIP SPRAY is the plastic coating that can be applied in a precise manner even on curved surfaces and areas difficult to reach with conventional film.

N.B. For best results we recommend to give Plasti Dip white background.

PlastiDip resists alkaline, acids, salts, moisture, abrasion, and most chemicals, and is an insulating dielectric coating.It will not crack, chip or peel, and will remain flexible even under severe conditions (-34ºc to +93ºc).

PlastiDip can be dipped, brush coated and sprayed. Add more layers for greater protection and grip.

Also... PLASTIC, RUBBER, FIBREGLASS and CONCRETE SURFACES!

NOTE: Surfaces which are non-absorbent such as metals should be primed using our recommended Primers, which are available in Clear and Grey.

PLEASE READ: Guide to Preparation and Application

The essential criteria is to ensure the surface is squeaky clean, grease, dirt, debris and contaminant free and thoroughly dry before coating.

On vehicles or irregular shaped items, particular attention should be paid to the sills, trim, gutters, grills, any tight or hard to get to corners and gullies that you would not normally concentrate on.

Wash only with hot water as some soap detergents contain residues that Plasti Dip may not adhere to.
Never use any petroleum, citric, alcohol or solvent based cleaning/care products with Plasti Dip.
Do not use car care cleaning products such as wheel shines, paint wipes etc, as these often leave trace residues which could cause adhesion problems.
Remove all traces of previous wax or silicone residue from cleaning products using the correct de-greaser, particularly for metal and plastic surfaces.
Clean large areas with Plasti Dip Panel Wipe degreaser.
Small areas can be cleaned with Plasti Dip “Dip Care Prep Degreaser”.
Ensure all water is removed and the area thoroughly dry before coating.

AEROSOLS – Refer to aerosol for instructions. Shake well before and during use. Test spray pattern on sample piece prior to application. In cold conditions, place aerosol in warm water (approximately 21°c) for 10-15 minutes before use.

BLAZE COLOURS – Best applied over white Plasti Dip base coat.

In common with all manufacturer's advice, we recommend testing on a small inconspicuous area first to ensure suitability. Base colours can alter the final shade.

If spraying, for a professional fine finish, Plasti Dip liquid should be filtered first. For best results, temperature of the spraying area should be between 10°c and a maximum of 27°c. Liquid Plasti Dip should be thinned 50/50 by weight. Apply the first coat as a mist coat and gradually build up the layers. The thicker the final coating, the easier it is to remove in the future should you wish. For vehicles, we suggest a minimum of 6-7 coats. For other projects a minimum of 2-4 coats is recommended depending on application method and coverage requirement.

Layers are touch dry and re-coatable in 30-45 minutes at 16-22°c and totally cured/dry 24-48 hours depending on temperature. Increase drying times in colder conditions.

Plasti Dip Primer is an adhesion promoter. Only use a primer to increase adhesion if you require a permanent coating. For permanent application, keying the surface with fine grit paper will improve adhesion if required.

For extra protection of your investment and ease of cleaning, we recommend using Dip Care Sealant over the final coating.

Please see our booklet supplied with your order for other handy tips and product information, including spray gun settings.

If you have any concerns about the correct products or procedures for your project, please feel free to contact us.