Victron 250w Mono Solar Panel Kit charging MPPT Smart Controller Battery Mounts

Victron 250w Mono Solar Panel Kit charging MPPT Smart Controller Battery Mounts Description

Solar Kit Contents

• 2 x 125w Monocrystalline Solar Panels 
• 20A Victron Smartsolar Charge Controller 12/24v 20A
• Solar PV to controller cable 
• Battery to solar controller cable
• 8 ABS Corner mounting brackets
• 1 ABS Cable entry
• 1 Tube of Sikaflex

Technical Specifications

125 Watt Solar Panel - (with 1m Cable & Solar Connector Plugs)

• Maximum Power (Pmax): 125W
• Maximum Power Voltage (VMP): 18.48V
• Maximum Power Current (IMP): 6.77A
• Open Circuit Voltage (VOC): 22.18V
• Short Circuit Current (ISC): 7.31A
• Weight: 6.20KG
• Size: 1070 x 580 x 30mm
• Cell Quantity 33
• Power Tolerance: +/-3%
• Maximum System Voltage: DC1000V

OUR NEW 9BB 125w Monocrystalline Solar Panels. These are our highest efficiency yet which now allows these panels to be slightly smaller and still generate the same power! 9BB means 9 silver conductor strips connect each row of silicone cells, which means higher efficiency in pulling every bit of power from all of the cells. The overall panel efficiency is now up from 18% to 21.2%.

Technical - Victron Energy SmartSolar Charge Controller  MPPT 100/20 

• Battery voltage (auto select) 12/24V
• Rated charge current 20A
• Nominal PV power, 12V 1a,b)290W
• Nominal PV power, 24V 1a,b) 580W
• Max. PV short circuit current 2) 20A
• Automatic load disconnect Yes
• Max. PV open circuit voltage 100V
• Peak efficiency 98%
• Self-consumption 12V: 25 mA 24V: 15 mA
• Charge voltage ‘absorption' 14,4V / 28,8V (adjustable)
• Charge voltage ‘float' 13,8V / 27,6V (adjustable)
• Charge algorithm multi-stage adaptive
• Temperature compensation -16 mV / °C resp. -32 mV / °
• Max. continuous load current  20A
• Low voltage load disconnect 11,1V / 22,2V / 44,4V or 11,8V / 23,6V / 47,2V or Battery Life algorithm
• Low voltage load reconnect 13,1V / 26,2V / 52,4V or 14V / 28V / 56V or Battery Life algorithm
• Protection Output short circuit / Over temperature
• Operating temperature -30 to +60°C (full rated output up to 40°C)
• Humidity 95%, non-condensing
• Data communication port VE.Direct

Enclosure

• Colour Blue (RAL 5012)
• Power terminals 6 mm² / AWG10
• Protection category IP43 (electronic components), IP22 (connection area)
• Weight 0,65 kg
• Dimensions (h x w x d)  100 x 113 x 60 mm

Standards

• Safety EN/IEC 62109-1, UL 1741, CSA C22.2

1a) If more PV power is connected, the controller will limit input power.

1b) The PV voltage must exceed Vbat + 5V for the controller to start.

Thereafter the minimum PV voltage is Vbat + 1V

2) A PV array with a higher short circuit current may damage the controller.

Solar Panels to Controller Cable

• 10m 4mm2 cable with male and female connectors to one end.

Solar controller to Battery Cable

• 1.5m, 4mm2 round profile cable, in-line fuse, 30A spade fuse M8 ring terminals.

All cabling carefully design to minimise voltage drops and maintain maximum system efficiency. TUV Approved 

Solar Brackets:

• ABS
• 4 Corners
• White
• Size per bracket 15x15x 6.5cm.
• Weight (4 brackets) 1.6kg 

• Easy Installation, holes should be drilled in each bracket, and corresponding holes in the solar panel frame on each side; then brackets should be fixed to the solar panel using self-tapping screws (not included).

  Cable Entry

  • ABS
  • Twin cable entry for 4-12mm cables
  • White
  • Watertight
  • Size: 12x10x5cm

  Product Warranties

  • Solar Panel = 10 Year for materials and workmanship
  • Charge Controller = 5 Year Victron Energy 
  • All other components have a 12 month warranty.